Professional Pool Service
Pool automation and control installation and repair in Chandler, AZ. Pentair, Hayward, and Jandy systems, retrofits, and app setup from Nevergreen Pools.
Nevergreen Pools provides pool automation & control in Chandler, installing and programming systems that run pumps, heaters, lights, valves, and sanitation from one control panel or app. We install and retrofit Pentair IntelliCenter and EasyTouch, Hayward OmniLogic and OmniHub, and Jandy iAquaLink systems, wiring in the low-voltage and communication lines the controller needs, then commission the system and walk the homeowner through the app before we leave.
Call us if the app shows the pool offline or won't connect no matter how many times you restart it, if the schedule stops running and the pump cycles on and off with no pattern, if a valve won't actuate when you switch from pool to spa, if the salt cell throws a fault or stops reporting output to the panel, if the touchscreen at the equipment pad has gone blank or frozen, if the heater won't fire on its scheduled start even though it runs fine on manual, or if the system on the pad is a control panel and app that were discontinued years ago and no longer take updates.
We serve Chandler in partnership with Beyond Pool Cleaning, a pool service company based nearby. Call to get a technician scheduled, or book your first visit online.
Most of the automation calls in Chandler start on a pad with a pump, heater, and salt system that were added a few years apart rather than installed together, so the first step is mapping what's actually there before we touch anything. We check what the existing controller can and can't talk to, whether the pump is single-speed, two-speed, or variable-speed, whether the heater has a digital interface or just a dial, and whether the salt cell communicates over its own line or shares a control board with the pump. On a full retrofit, we replace the aging panel with a Pentair IntelliCenter or EasyTouch, a Hayward OmniLogic or OmniHub, or a Jandy iAquaLink system depending on what's already installed and what the homeowner wants to control from a phone. We run new low-voltage and communication wiring to the pad, valves, and any water features, since a lot of the original wiring in older installs was never pulled with automation in mind and won't carry a modern control signal reliably.
Once the controller is in, we program the actual schedule: filtration run times built around a variable-speed pump's slower, longer cycles rather than a single-speed pump's on/off routine, heater set points and lockouts so it doesn't run during the coldest early morning hours in winter, spa jets and water features on their own timers, and lighting scenes if the system supports it. We wire in pH and ORP sensing where the equipment supports it, so the controller adjusts chemical feed automatically instead of running on a fixed timer that ignores bather load and heat. Every valve gets tested through a full pool-to-spa cycle, every schedule gets run through once end to end, and we check that the app connects reliably from inside and outside the house before we call the job done.
Commissioning ends with training, not a handoff. We walk through the app on the homeowner's own phone, show how to override a schedule for a party or a cold snap, and confirm notifications are set up so a fault, like a salt cell losing output, shows up as an alert instead of getting discovered a week later when the water turns.
A pool automation system that's set up right means you can check the pool from the office, turn the heater on an hour before you get home, and get an alert the moment something stops working instead of finding out when the water turns green after a week of nobody watching it. It also means the schedule actually matches how the equipment runs, a variable-speed pump filtering on the cycle it was built for instead of the on/off pattern left over from whatever pump used to be on the pad, so the system uses less power and the parts last longer.
Left alone, an old or partly-working automation system tends to fail quietly. A valve that won't fully seat wastes water and chemical running the spa and pool at once without anyone noticing. A schedule that never got updated after a pump swap can run a variable-speed motor at full speed around the clock, which shortens its life and shows up on the power bill. A discontinued app that stops getting updates eventually stops connecting altogether, and at that point the system runs whatever schedule was last programmed with no way to change it short of a technician visiting the pad directly.
Call to get a technician out to look at what's on your pad now, or book your first visit online and we'll start with a full check of the existing system before we recommend anything.
Related services in Chandler: Pool Repair in Chandler and Pool Maintenance in Chandler.
