Professional Pool Service
Nevergreen Pools installs and repairs pool automation and control systems in Mesa, AZ, from new Pentair and Jandy panels to retrofits on older equipment pads.
Nevergreen Pools installs pool automation & control in Mesa, covering new Pentair IntelliCenter and EasyTouch systems, Hayward OmniLogic and OmniHub systems, Jandy iAquaLink systems, pump and heater scheduling, valve actuators, app control setup, pH and ORP sensing, and retrofits of automation onto older equipment pads that were never wired for it.
Call us if the app on your phone won't connect to the equipment or keeps dropping connection, if the pump only runs when someone manually flips it at the pad instead of following its schedule, if the control panel shows an error code or a blank display, if the heater or salt cell won't respond through the app even though it works when triggered by hand, if a valve is stuck and the system can't switch between pool and spa, if the pH or ORP reading on the panel doesn't match a manual test kit, or if the automation was installed years ago and no longer matches the pump or heater sitting on the pad now.
We serve Mesa in partnership with Beyond Pool Cleaning, a pool service company based nearby. Call to get a technician scheduled, or book your first automation visit online.
The starting point is always the equipment pad, not the app. West and central Mesa still have plenty of pools from the 1970s and 1980s running on original plumbing, older skimmers, and single-speed pumps, so a retrofit there means adding relays, actuators, and a control panel to a pad that was never wired for any of it. East Mesa has more pools built with variable-speed pumps, salt systems, and some automation already in place, so that work is usually an upgrade or a replacement of a failing panel rather than a full build-out. Either way, we start by identifying every piece of equipment on the pad, its make and model, and whether it's compatible with the control system going in, since a Pentair panel won't run a Jandy valve actuator and a universal relay isn't always the right fix.
Once we know what we're working with, we run the low-voltage and communication wiring between the panel, the pump, the heater, the valves, and any lights, then mount and wire the control unit itself. Pumps get programmed with separate speeds for filtration, cleaning, spa, and water features rather than one fixed setting, since a single-speed schedule wastes electricity and doesn't take advantage of what a variable-speed pump can do. Heaters get set with target temperatures and time windows instead of being left to run on manual override. If the system includes pH or ORP sensing, we calibrate the probes against a manual test kit before we trust the reading on the panel, because a scaled or fouled probe will report numbers that don't match what's actually in the water. Hard water here also means the salt cell and heater exchanger scale up over time, which throws off both output and sensor accuracy if it isn't checked.
Summer heat here runs pumps and heaters harder and longer than in most climates, and monsoon dust storms put a layer of grit into the pool overnight, so we set filtration schedules that account for both instead of using a factory default. On rental and seasonal properties where the owner isn't on site most of the year, we also set up remote alerts so a pump failure or a heater fault shows up on the app instead of going unnoticed for weeks.
A correctly installed system means you can check on the pool from your phone instead of walking out to the pad, adjust the heater before guests arrive, run the cleaning cycle without touching a valve by hand, and get an alert if the pump or salt cell stops working instead of finding out when the water turns green. It also means the equipment runs on schedules matched to actual conditions, filtering longer through the worst of summer heat and after monsoon dust storms, rather than a generic setting left over from installation day.
Left alone, a mismatched or aging automation system tends to fail quietly. Valves stick in one position, sensors drift out of calibration and the panel starts reporting numbers that don't match the water, and pumps left on manual override run at full speed around the clock, which costs more in electricity than the repair would have. On older pads, wiring that was patched together over the years becomes harder to diagnose the longer it's left as is. Call us to get a technician out to inspect the pad and the current control setup, or schedule an install or retrofit online.
Related services in Mesa: Pool Repair in Mesa and Pool Maintenance in Mesa.
