Nevergreen Pools provides pool maintenance in Arcadia, with plans that range from full-service weekly care to chemical-only visits, seasonal adjustments as the water heats up and cools down through the year, and a maintenance record that tracks every filter clean, every salt cell clean, and the age of each piece of equipment on the pad. Pools here split into two groups: 1950s and 1960s plaster pools with original plumbing that has never been touched, and newer pebble pools built during recent teardown rebuilds, with automation panels and salt systems. The plan we set up depends on which one you have.

Call us if the tile line keeps growing a ring of white scale no matter how often you wipe it down, if leaves and mesquite pods from nearby trees fill the skimmer baskets every two or three days, if the deck or the coping has started to crack or heave near a low corner of the yard, if the water level drops faster than the heat can account for, if the plaster on an older pool feels rough or chalky underfoot, if the salt cell is putting out less chlorine than it used to, or if a monsoon storm leaves the water cloudy or green the next morning.

We serve Arcadia in partnership with Beyond Pool Cleaning, a pool service company based nearby in Scottsdale. Call to set up a maintenance plan, or book your first visit online.

Setting Up the Plan

The first visit starts with a walk of the equipment pad and a full water test, since Arcadia's water is hard enough that it changes how we set the chemistry program before we do anything else. On an older plaster pool we check the finish for etching, chalking, and scale, and we look at the plumbing at the pad for original galvanized or copper fittings, since those are the parts most likely to have worn out after fifty or sixty years. On a newer pebble pool we check the automation panel, the salt cell for scale buildup, and the variable-speed pump settings. We also note any dampness or soft ground near the shell or the deck, since flood irrigation in older parts of the neighborhood raises the water table enough to push moisture up under a pool that has any weak spot. Citrus, palm, and mesquite trees on most lots here mean the skimmer and pump baskets fill fast, so we check how often those need to be pulled and set the visit schedule around it.

After that first visit, the plan runs on one of two tracks. Full-service means we handle everything on every visit: testing, chemical dosing, skimming, brushing, vacuuming, basket cleaning, and equipment checks. Chemical-only means we test and balance the water and leave the physical cleaning to you or a pool cleaner you already use. Either way, we keep a record of every filter clean, every salt cell clean, and the age of the pump, heater, and cell, so replacement decisions are based on real wear instead of guesswork.

• Test and balance chlorine, pH, alkalinity, and stabilizer, adjusted for the day's heat
• Skim the surface and empty skimmer and pump baskets, which fill fast under citrus and mesquite trees
• Brush walls, steps, and the waterline where hard water scale forms first
• Check pump, filter pressure, heater operation, and salt cell output
• Clean the filter or the salt cell on a schedule set by pressure and output readings, not the calendar
• Adjust the chemical program seasonally as bather load and heat change through the year

In summer the plan shifts toward closer attention to evaporation, since a pool here can lose an inch of water a week in peak heat, and that changes how fast chemicals need topping off. After a monsoon storm we test before we do anything else, because dust and runoff can knock chlorine and pH out of range in a single afternoon. In winter, with the pool used less, we stretch out the physical cleaning but keep testing on the same interval, since a pool that sits unused can still scale or lose sanitizer overnight.

Repairs and Equipment

When something on the pad needs attention, we write up what we found and what it takes to fix on the same visit, and our own techs handle the repair instead of routing it to a subcontractor. On a 1950s or 1960s pool, that often means original copper or galvanized lines at the pad that have corroded at the unions, or a single-speed pump that runs louder and less efficiently than what is available now. On a newer pebble pool, it is more often a salt cell that has scaled up faster than expected because of how hard the water is, or an automation panel that needs a sensor replaced. We give a straight answer on repair versus replacement: a pump or heater with one bad part is usually worth fixing, but a motor running on worn bearings or a heat exchanger scaled from years of hard water usually is not, since the running cost of an old unit adds up faster than a repair bill. Any pump we install goes in as a variable-speed unit programmed for filtration, cleaning, and spa speeds separately, because a pool run on one fixed speed wastes electricity every day it runs.