Professional Pool Service
Licensed pool automation and control installs, retrofits, and programming for homeowners in Shingle Springs, CA. Call Nevergreen Pools today.
Nevergreen Pools handles pool automation & control in Shingle Springs, installing and programming the systems that run a pool's pump, heater, lights, and valves from a wall panel or phone app: Pentair IntelliCenter and EasyTouch, Hayward OmniLogic and OmniHub, and Jandy iAquaLink, along with the pH and ORP sensors that monitor water chemistry without a test kit every day.
Call us if the water chemistry swings even though nothing on the pad changed, if the app shows a schedule running but the pool stays cloudy because filtration times no longer match how the pool gets used, if the spa will not switch over to pool mode or a valve does not actuate when you press the button, if the pH or ORP reading on the panel does not match what your test strip shows, if the heater will not hold a set temperature or will not fire from the app, if the control panel or remote has stopped responding and you are back to running everything by hand at the pad, or if a hard freeze is coming and you are not sure the system will protect the pump and exposed plumbing overnight.
Nevergreen Pools is a licensed pool company based in Shingle Springs, serving the Sacramento region, including Cameron Park, El Dorado Hills, Placerville, and Rescue. Call to get a technician scheduled, or book your first visit online.
We start at the equipment pad with a walk of what is already there. Many properties here sit on larger rural and semi-rural lots, so there is often a long run of pipe and wire between the pool and the pad, and the pad itself is usually sitting out exposed to the weather rather than tucked against the house. Before anything gets mounted we check whether the existing low-voltage and communication wiring can carry an automation signal or whether we need to run new wire, and we confirm the panel enclosure and any valve actuators we install can hold up outdoors through both summer heat and winter freeze. On an older pad still running on mechanical timers and a standalone heater dial, this is a full retrofit: new relays, new valve actuators if the pool has a spa or water feature, and a control board sized to the equipment that is actually there, not a generic kit.
Once the hardware is in, we program the schedule around the pool's real use, not a default template. That means filtration run times that stretch longer through the swim season from May to October and pull back in the off months, with extra run time built in during fall when oak and pine debris is heaviest so the pump and skimmer baskets are not overwhelmed between service visits. We set heater setpoints and run windows, and we program a freeze protection routine that kicks the pump on automatically when the panel's temperature sensor drops near freezing, since a hard freeze on an unprotected system can crack a pump housing or split exposed plumbing on the pad overnight. We also install and calibrate the pH and ORP sensors so the feed pumps dose off actual readings instead of a timer, which matters most on well-fed properties where mineral content pushes chemistry around on its own, and on pools filled from district water where the chemistry needs calcium and alkalinity held steady instead of drifting.
We test every function before we leave: pump speeds, heater ignition, valve actuation, sensor readings against a manual test, and the freeze protection trigger. Then we walk the homeowner through the app itself, how to override a schedule, how to check sensor readings, and how to tell if something on the pad needs a service call instead of a settings change.
A properly commissioned system means you stop guessing. The pump runs at the speed and duration the pool actually needs, the heater holds its setpoint instead of cycling on manual calls, chemistry gets corrected off real sensor data instead of a weekly test strip, and the system protects itself the first cold night of the year without anyone remembering to do it by hand. On a pool with a spa or water feature, mode switching happens on a schedule or a tap instead of a trip to the pad to turn valves by hand.
Left on an old timer and a manual heater dial, or on an automation system nobody ever programmed past the factory defaults, the pool runs on guesswork. Filtration either runs too little and the water clouds up, or runs around the clock and wastes power for no benefit. A missed freeze means a cracked pump housing or split plumbing on the pad, which is a bigger repair than the automation upgrade would have cost in the first place. And pH left to drift on a well-fed pool shows up as scale building at the waterline and etching in the plaster months before anyone catches it on a test strip.
If your system is not doing any of that for you right now, call us and we will walk the pad, check what you have, and tell you straight whether it needs a full retrofit or just a reprogram.
Related services in Shingle Springs: Pool Repair in Shingle Springs and Pool Maintenance in Shingle Springs.
