Professional Pool Service
Nevergreen Pools repairs skimmers, valves, unions, and pool cleaners in Peoria, AZ. We diagnose the problem and give an honest repair or replace call.
Nevergreen Pools provides pool repair in Peoria, covering cracked or broken skimmers and skimmer lids, broken return fittings and eyeballs, leaking unions and valves on the equipment pad, stuck or broken diverter valves and valve actuators, cracked pad plumbing, pressure problems from clogged lines or a failing valve, main drain and skimmer basket issues, and pool cleaner repairs.
Call us if a skimmer lid is cracked and the opening keeps chipping wider, if water is dripping or spraying from a union or valve on the equipment pad, if a return fitting eyeball is stuck or won't aim the water where you point it, if a diverter valve is stuck between settings or the actuator hums without turning, if filter pressure climbs fast and won't drop after a backwash, if a skimmer or pump basket has cracked and won't seat in its housing anymore, or if the pool cleaner has stalled out or stopped climbing the walls.
We serve Peoria in partnership with Beyond Pool Cleaning, a pool service company based nearby. Call to get a technician out, or book your first visit online.
Repair calls climb in late spring, when pumps shift to longer summer run times and plastic fittings that spent months in full sun finally give out under the added hours and pressure. A tech starts at the equipment pad, since most repair calls trace back to a handful of spots: the unions at the pump and filter, the valves that route water to the pool, spa, or cleaner line, and the plumbing joints behind them. Plaster pools built in the 1980s and 1990s often have original PVC unions and gate valves that have gone brittle from decades of Arizona sun, and those are usually where a slow leak or a stuck valve shows up first. Newer pebble-finish pools with variable-speed pumps and electronic valve actuators fail differently, usually at the actuator motor or the circuit board rather than the valve body itself.
Pressure problems are usually a process of elimination, not a single obvious cause. A pump that has lost prime, a valve stuck between settings, or a line partially blocked by monsoon debris can all produce the same symptom on the gauge, high pressure and weak flow at the returns. We check pressure at each valve position and each section of pad plumbing until we find where it changes, rather than replacing the first part we suspect. On multi-port valves that route water to the pool, spa, and cleaner line, a worn O-ring or a cracked valve body can also let water cross over between lines, which shows up as low pressure in one line and high pressure in another. Confirming which one it is before replacing a part is what keeps one repair from turning into a second one a few months later.
Once we find the failed part, we give a straight answer on repair versus replacement. A cracked union, a torn valve diaphragm, or a broken skimmer lid gets swapped on the spot in most cases. A valve body that is cracked through, a return fitting that has stripped its threads, or plumbing that has failed at more than one joint usually means replacing the section rather than patching around it, since a patch on brittle PVC tends to crack again within a season. Skimmer and pump baskets take a beating from monsoon dust and windblown grit and are checked for hairline cracks that let debris bypass the basket and reach the pump. Main drain covers get checked for cracks or missing screws, since a loose or broken cover is a safety issue as much as a repair. Pool cleaner repairs cover the drive belt, the diaphragm, worn wheels, and tangled or kinked hose that keeps the unit from climbing the walls or turning at the far end of the pool.
A pool with no drips at the pad, valves that switch clean between settings, returns that aim where you point them, and a cleaner that actually covers the floor instead of parking in the deep end. Ignore a small leak at a union or valve and it usually gets worse, not better, since the constant moisture erodes the fitting further and can undermine the deck or equipment pad slab underneath it. A cracked skimmer lid left alone widens with every hot afternoon until it becomes a tripping hazard or lets debris straight into the basket. A stuck diverter valve left unrepaired also runs the pump against unnecessary resistance, which shortens motor life on top of whatever the original problem was. Since many households in Peoria are out during the day, we schedule repair visits around when you're actually home, or work directly at the pad if you'd rather not wait around, and we text you the same day with what we found and what it costs to fix. Call to get a technician out, or schedule a repair visit online.
Related services in Peoria: Pool Pump Repair in Peoria and Automation & Control Systems in Peoria.
