Professional Pool Service
Pool automation and control installs in Arcadia, AZ from Nevergreen Pools. Pentair, Hayward, and Jandy systems, app control, scheduling, and retrofits.
Nevergreen Pools provides pool automation & control in Arcadia, covering new system installs, retrofits on older equipment pads, pump and heater scheduling, valve automation, app control, water chemistry sensors, and homeowner training on the finished system.
Call us if you're still walking out to the equipment pad every morning to switch the pump on and off by hand, if you're turning a valve manually to swap between pool and spa, if the pump runs on one speed all day because nobody ever set a schedule, if an existing automation panel won't connect to the app anymore, if you're guessing at chlorine and pH with a test strip instead of getting a sensor reading, if the heater has to be lit and adjusted by hand every time someone wants to swim, or if a remodel left the pad rewired but the automation panel was never hooked up and programmed.
We serve this area in partnership with Beyond Pool Cleaning, a pool service company based nearby. Call to get a technician scheduled, or book your first visit online.
The first step is a walk of the equipment pad to see what's already wired and what isn't. A lot of pads built before automation was standard have a single-speed pump, a standalone heater, and valves that only ever get turned by hand. We check what brand of pump, heater, and salt or chlorine system is already on the pad, since that decides whether we build the system around a Pentair IntelliCenter or EasyTouch, a Hayward OmniLogic or OmniHub, or a Jandy iAquaLink panel. Many pools on lots like these are 1950s and 1960s plaster on the original plumbing, while newer pools going in on recent teardown rebuilds are pebble finish with salt systems already on the pad, and the wiring approach is different for each. On a full retrofit we run new low-voltage control wiring and communication cable from the panel to every pump, valve actuator, and heater, and we seal each connection against monsoon dust and the groundwater that flood irrigation pushes up under older pads and decks. Where the existing electrical at the pad can't support a new variable-speed pump or a control panel, we address that before any automation component goes in, since a panel wired into undersized circuits will trip and fault instead of running clean.
Once the panel is wired in, we program every piece of equipment it controls:
We commission the system on site, running every mode from the app before we leave, and we walk the homeowner through the controls so they know how to override a schedule, switch to spa mode, or read a fault alert before it turns into a bigger repair. Citrus, palm, and mesquite trees drop leaves, fruit, and fronds into the pool most of the year on lots like these, so we also set a cleaning cycle timed around the heaviest drop instead of one general afternoon block, and we check that the skimmer line and pump basket can keep up with it before we sign off on the install.
A pool with automation done right runs itself. The pump ramps to the right speed for filtration, cleaning, or spa without anyone touching a switch, the heater holds its temperature through the day, valves switch automatically for spa mode or a water feature, and chemistry gets checked and corrected by sensors instead of a test strip left on the counter. The homeowner gets an app that shows the pool's actual status and lets them make a change from anywhere, instead of a panel nobody in the house knows how to use, and a system that flags a fault instead of quietly running a pump dry or a heater with no water moving through it.
Leaving an old pad unautomated costs more than convenience. A single-speed pump that runs all day on one setting burns more electricity than a scheduled variable-speed pump ever will, and it wears out sooner running full speed for tasks that only need a fraction of that flow. A heater that gets lit and adjusted by hand tends to get left running when nobody's swimming, or left off when someone wants to use the pool, because there's no schedule doing it automatically. Chemistry that only gets checked when someone remembers to test it drifts further in this heat than it would somewhere cooler, and that drift is what leaves permanent scale on the tile line and turns a pool cloudy faster than expected after a monsoon storm blows dust across the water overnight. Call us to get a new system installed or an existing panel wired back in and working, or book a visit online.
Related services in Arcadia: Pool Repair in Arcadia and Pool Maintenance in Arcadia.
