Professional Pool Service
Nevergreen Pools repairs skimmers, valves, pad plumbing, and pool cleaners for homeowners in Rocklin, CA. Call today or book your first visit online.
Nevergreen Pools provides pool repair in Rocklin, covering cracked or broken skimmers and skimmer lids, broken return fittings and eyeballs, leaking unions and valves at the equipment pad, stuck or broken diverter valves and actuators, cracked plumbing at the pad, low pressure from clogged lines or a failing valve, main drain and skimmer basket problems, and pool cleaner repairs.
A cracked skimmer, a stuck valve, or a leaking union does not get better on its own, and every month it sits unrepaired costs you water, chemicals, or power you do not need to spend. Call us if a skimmer lid is cracked or will not sit flush, if a return eyeball is missing or stuck and will not aim water flow, if a union or valve at the pad is weeping and leaving a wet spot on the deck, if a diverter valve is stuck between settings or the actuator has stopped moving it, if filter pressure keeps climbing faster than normal between cleanings, if the main drain cover or a skimmer basket is cracked or missing, or if your pool cleaner keeps stalling in the same spot or will not climb the walls.
Nevergreen Pools is a licensed pool company based in Shingle Springs, serving the Sacramento region. Call to get a technician out, or book your first visit online.
We start at the pad and work backward to the pool. A pressure gauge that reads high with a clean filter usually points to a closed or partially stuck valve, not the filter itself, so we isolate each valve one at a time to find which one is not fully opening. A gauge that reads low along with weak returns usually means a suction side leak, an air leak at a union, or a clogged impeller, and we check each in that order because an air leak at a union is the easiest fix and the most common one we find on pads that have not been touched in a few years. Unions and valve o-rings dry out and crack from UV and heat, and a union that is weeping a few drops an hour will be pulling in air on the suction side long before it leaks enough to notice on the deck.
At the pool itself, we check every skimmer lid, throat, and basket for cracks, check return fittings and eyeballs for wear that keeps them from holding an angle, and check the main drain cover for cracks or a missing screw. Pad plumbing that was glued decades ago can crack from ground settling or from a freeze, and a crack that only shows as a damp spot under the equipment pad can be easy to miss until pressure drops further. Because the water here comes from the Placer County system and runs low in calcium and alkalinity, pH drifts faster than it does on harder water, and that drift is part of why older glued joints and gaskets fail sooner than the rated life of the part. We also check the diverter valve and actuator on any pool with automation, since a motorized valve that stalls partway through its turn will throw off flow to the spa, the cleaner line, or a water feature even though the pump is running fine.
Once we know what is actually wrong, we give you a straight answer on repair versus replacement before doing the work. A cracked skimmer lid, a worn o-ring, or a stuck actuator gets repaired, since those are inexpensive parts with a clear fix. A valve body that is cracked at the pad, a basket holder that has broken off inside the skimmer housing, or plumbing with more than one failure point in the same run is usually worth replacing outright, because a patch on brittle pad plumbing tends to fail again at the next joint within a season.
A repaired pool holds pressure where it should, every valve moves water where you point it, and the skimmers and returns do their job without a wet spot showing up on the deck. That matters more over a full season than it sounds. A pool that circulates correctly needs less chlorine to stay clear, and equipment that is not fighting a stuck valve or an air leak lasts longer before the next repair call. Leave a small leak or a stuck valve alone and it does not stay small. A weeping union pulls in air and starves the pump of water over time, which can burn out a pump that would otherwise have lasted years. A cracked skimmer lid left in place lets debris into the line and can crack further with the first freeze. A main drain cover that is missing is also a safety issue, since an open drain creates suction risk for anyone in the pool.
Call Nevergreen Pools to get a technician out to look at the pad and the pool, or book your first visit online. We will tell you what is actually broken, what it costs to fix, and whether it makes sense to repair the part or replace it.
Related services in Rocklin: Pool Pump Repair in Rocklin and Automation & Control Systems in Rocklin.
